Reinforced GF-N T profile

On the outside they are identical, Ø 28 mm. The T has a reinforced inner wall: it weighs 0.79 kg/m instead of 0.37 and is about 1.5 times more resistant to bending. Over a 1000 mm span it takes 289 N at mid-span against 195 N, at the same deflection.

In terms of stiffness they are close: the T is about 1.5 times the standard pipe, the Hard about 1.7. The Hard is designed for joints that take continuous impacts and has its own dedicated inner connector, end cap and threaded insert for feet; the T has an M8 thread at the end for feet. Choose according to where the pipe goes.

Yes: the end of the T is threaded M8 to a depth of 24 mm and the levelling foot screws in directly, without a threaded insert. Let us know with your cutting order.

GF-N outer connectors, the same as for the standard pipe. To close the end there is the dedicated inner end cap GFA-410 or the outer end cap GFA-401.

When a cross member or upright is working at its limit but you do not want to change diameter or dimensions: more heavily loaded shelves, uprights with screwed-in feet, trolley frames. You put it only where needed; the rest stays in standard pipe.

Move to the GF-N W mounted upright: over a 1000 mm span it takes about 1950 N at mid-span with 5 mm of deflection, almost seven times the T. For heavily loaded uprights use the GF-G Ø 43 series.

The standard GF-N profile is suitable for most uprights and cross members. If a cross member is long or loaded use the GF-N W fitted upright (about 10 times stiffer), or the T (about 1.5 times) or the Hard (about 1.7 times, also for joints that take impacts), which have the same diameter. To fix plate castors, panels or rollers with T-nuts choose the profile with C10 slot; F35 and F50 have a flat flange for labels, small parts holders and supports. The sliding profile has a smooth surface for sliding parts and boxes, the round roller profile becomes a roller with the pin connectors, LS and LS with S slot carry a linear slide and the linear guide profile is the track for the linear rollers.

The GF-N Ø 28 is the standard for workstations, flow racks and trolleys. The GF-S Ø 19 weighs about half as much (0.20 kg/m versus 0.37) and is for light frames, dividers, guards and small mechanisms. The GF-G Ø 43 is for uprights and cross members that have to carry a lot: over a 1000 mm span it supports 851 N at the centre versus 195 N for the GF-N, for the same deflection. It is often worth mixing them, for example GF-G uprights and GF-N cross members joined by mixed connectors.

Yes. Green Frame profiles can be ordered as 4000 mm bars or cut to the length you need: we do the cutting ourselves, in our workshop. Give us the dimensions of the pieces or send us a sketch of the structure and we will prepare the cutting list.

Yes. The standard series is GF-N (Ø 28 mm pipe); GF-S (Ø 19 mm) is lighter and more compact, GF-G (Ø 43 mm) is for stiffer structures. There are mixed connectors that join pipes from different series, for example a Ø 19 or Ø 43 pipe to a Ø 28 pipe, so you use the right diameter at every point of the structure.

No. The connectors are fixed to the pipe with hex socket screws: a hex key is all you need. Loosen the screw, insert the pipe, bring it into position and tighten. No welding, drilling or painting.

Yes, it is the strength of the pipe system: loosen the connectors, move or replace the pipes and retighten. You can raise a shelf, extend a workbench or reuse the components in another structure when the process changes, with continuous improvement in mind.

Yes. We can design the structure (workstation, flow rack, trolley, line-side supermarket) with the load calculation and deliver it to you assembled or as a kit with the parts already cut and the list of components.

No. Profiles and connectors are in anodised aluminium: the surface resists corrosion and wear without painting and is easy to clean.

Yes. The range includes conductive components such as ESD inner end caps, ESD clips for electrical continuity between pipe and connector, and ESD inserts for levelling feet and castors. Tell us which EPA area you work in and we will tell you the components to use.