Skip to Content
  1. All Products
  2. AL Modular System
  3. Connection elements
  4. Screws and anchors
  5. Foundation screw for concrete 10x100
Vite di fondazione per calcestruzzo 10x100

Foundation screw for concrete 10x100

https://leanproducts.eu/web/image/product.template/3557/image_1920?unique=1d9bc53

SW15 10x100 foundation screw for anchoring structure feet and base plates to cracked and non-cracked concrete floors. It is driven in with an impact wrench and can be readjusted up to twice after installation.

Read more ↓
Code: 3842564815
  • Brand
  • Technical notes
  • Length mm
  • ESD
  • Diameter mm

This combination does not exist.

Log in to see prices and buy
You have already submitted a query for this product today.
Bosch 5S1
Contact Us
Request a quote
We reply within 1 working day
Download PDF data sheet

Specifications

Brand Bosch Rexroth
ESD yes
Technical notes Foundation screw SW15 for cracked and non-cracked concrete; readjustable up to 2 times
Diameter mm 10
Length mm 100
Tags
Tags
Bosch 5S1

The floor anchor is the classic alternative. The foundation screw is driven directly into the concrete with an impact wrench and can be readjusted up to twice.

With the floor fixing wall plug: Ø 8x80 for the 135x135, Ø 10x90 for 120x120 and 150x150, Ø 8x95 for the 270x360. For 120x120 and 150x150 you can also use the foundation screw for concrete. Use the washers to compensate for unevenness.

No, this product includes only the washers. The floor fixing wall plug and the foundation screw for concrete are separate items.

It is one of the accessories for the 120x120 and 150x150 base plates flush with the posts, along with the floor anchor and the compensating washers.

The AL foot with the Ø 8x95 wall plug and the 1 or 3 mm washer for round feet; the 45x45 foot with the foundation screw for concrete and the Ø 23 washer.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.