Skip to Content
  1. All Products
  2. AL Modular System
  3. Cover caps and cover profiles
  4. Cover caps for brackets and connectors
  5. Cover cap for bolt connector and longitudinal end connector

Cover cap for bolt connector and longitudinal end connector

https://leanproducts.eu/web/image/product.template/3576/image_1920?unique=1d9bc53

PP cover cap for closing the holes of the bolt connector and the longitudinal end connector: D11 x 23.5 for slot C8, D17 x 44.6 for slot C10. Signal grey or black ESD, to finish the connection.

Read more ↓
Code: 3842551052
from
not with
options
Prices per piece + VAT
Prices per pack of %s + VAT
Prices per pack of %s pcs + VAT
colors
only
of
available
  • Technical notes
  • Size
  • Diameter mm
  • ESD
  • Length mm
  • Material
  • Colour
  • Brand

This combination does not exist.

Log in to see prices and buy
You have already submitted a query for this product today.
Bosch 5S1
Contact Us
Request a quote
We reply within 1 working day
Download PDF data sheet

Specifications

Technical notes Cover cap for bolt connector / longitudinal end connector
Size D11x23.5
ESD yes
Diameter mm 11
Length mm 23.5
Material PP
Colour grey
Brand Bosch Rexroth
Tags
Tags
Bosch 5S1

D11 x 23.5 for the bolt connector D11 on profiles with slot C8; D17 x 44.6 for the bolt connector D17 and for the longitudinal end connector on profiles with slot C10.

Yes, the connector creates a conductive connection, but the grey cover caps included in the set are not ESD conductive. In an ESD area replace them with the black D17 x 44.6 cover caps.

Bolt connector and longitudinal end connector create a conductive connection, but the grey cover caps included in the sets are not conductive. In an ESD area use the black cover caps.

Yes, it creates a conductive connection between the profiles. The two grey cover caps included are not conductive: if the joint must be fully ESD, close the holes with the black ESD cover caps.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.

Accessory Products