Skip to Content
  1. All Products
  2. AL Modular System
  3. Connection elements
  4. Connectors and fittings
  5. Bolt connector

Bolt connector

https://leanproducts.eu/web/image/product.template/2918/image_1920?unique=1d9bc53

Zinc-plated steel bolt connector for joining two profiles with slot C8 or C10 at right angles, even in closed frames: it withstands high loads and torsion, up to 5000 N. Requires a D11 or D17 through hole in the profile.

Read more ↓
Code: 3842554402
from
not with
options
Prices per piece + VAT
Prices per pack of %s + VAT
Prices per pack of %s pcs + VAT
colors
only
of
available
  • ESD
  • Slot
  • Surface treatment
  • Load capacity Fmax N
  • Tightening torque Nm
  • Production method
  • Technical notes
  • Moment Mmax Nm
  • Diameter mm
  • Length mm
  • Material
  • Size
  • Brand

This combination does not exist.

Log in to see prices and buy
You have already submitted a query for this product today.
Bosch 5SP
Contact Us
Request a quote
We reply within 1 working day
Download PDF data sheet

Specifications

Slot C8
ESD yes
Surface treatment Zinc plating
Load capacity Fmax N 2500
Moment Mmax Nm 1000
Tightening torque Nm 25
Production method Moulding
Technical notes Raccordo per bulloni D11x11, 8/8
Diameter mm 11
Length mm 11
Material Zinc-plated steel
Size D11x11
Brand Bosch Rexroth
Tags
Tags
Bosch 5SP

The QV set holds 1000 N, but it is not designed for bending of the joint. If the crossbar is cantilevered or carries side loads, use a T-connector or a bolt connector.

The one matching the width of the profile the connector passes through: D11x30 for profiles 30, D17x45 for 45, D17x90 for 90 and so on. To connect a profile 30 to a profile with slot C10, use the D11x30 C8/C10 version.

A transverse through hole in the profile being crossed: D11 for the D11x30, D17 for the D17 versions. You can make it with the drilling jig.

The D11x30 holds 2500 N, the D17 from 40 to 60 mm 4000 N, the D17 from 80 to 100 mm 5000 N. The moments also increase with the section, up to 1000 Nm with the D17x100. These are static limit values: apply your own safety factors.

The T-connector needs no holes on profiles 40, 45 and 50 and reaches 9000 N on the 45x45. The bolt connector needs the through hole, but also withstands torsion, fits in a closed frame and covers profiles up to 100.

Yes, it creates a conductive connection between the profiles. The two grey cover caps included are not conductive: if the joint must be fully ESD, close the holes with the black ESD cover caps.

Yes, it also fits in closed frames: drill the through hole, insert the connector and tighten it to 6 Nm (D11) or 25 Nm (D17) without removing the adjacent profiles.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.

Accessory Products