Pudu MT1 VAC Sweeping and Vacuuming Cleaning Robot

It is the MT1 series model that combines sweeping, vacuuming and dust mopping. It works on hard floors and on short-pile or industrial carpet and retains fine dust with the HEPA H11 filter. Compared with the MT1 it collects less bulky waste (6-litre container plus 14 litres of dust bags), but vacuums and filters dust better. It cleans up to 1,400 m²/h. It does not scrub and does not pick up liquids.

They are three sweeping robots with the same base (84 × 60 cm) and AI waste recognition. The MT1 dry-sweeps large indoor areas with hard floors: up to 1,800 m²/h, 35-litre bin, 4–8 hours of runtime. The MT1 Vac adds vacuuming and a dust mop, has a HEPA H11 filter and also works on carpet: up to 1,400 m²/h and a 20-litre collection capacity. The MT1 Max is the most powerful: 3D LiDAR, IP54 protection rating, up to 2,200 m²/h and 6.5–10 hours of runtime, also designed for car parks and covered semi-outdoor areas.

It depends on the dirt and the surface. The MT1 series dry-sweeps: it is the right choice for dust, debris and packaging over large areas, from 1,400 to 2,200 m²/h. The CC1 is a 4-in-1 floor scrubber-dryer robot for medium-sized indoor areas: it scrubs, sweeps, vacuums carpet and removes dust, at 700–1000 m²/h. The BG1 is the autonomous scrubber-dryer for large areas: it sweeps and scrubs in a single pass and recognises spilled liquids. It often pays to combine them: an MT1 for daily sweeping, a CC1 or a BG1 for scrubbing.

Up to 1,400 m²/h, with a 70 cm sweeping width and 55 cm vacuuming width. It collects 20 litres in all: two 7-litre dust bags and a 6-litre waste container. Runtime ranges from 3 to 6.5 hours, depending on the mode.

No. All three models work dry only: they sweep and, in the case of the MT1 Vac, vacuum and run the dust mop. They have no water tanks and do not pick up liquids; they should not be used on very oily floors or with standing water. To scrub and dry floors you need PUDU scrubber-dryers, such as CC1 or BG1.

Yes: short-pile carpet and industrial carpet, as well as hard floors. AI floor recognition detects when it moves from carpet to hard floor and adjusts suction, pressure and brush speed. On 1,000 m² of carpet it works for up to 10 consecutive days before it needs emptying. With the optional extension for manual vacuuming you can also clean the sides of sofas, walls and glass partitions.

It is designed for level indoor areas with hard floors or carpet: airports, metro stations, hotels, offices, conference centres and shopping centres. It should not be used outdoors (its protection rating is IPX3) or on very oily floors. It climbs thresholds up to 20 mm and gaps up to 30 mm, climbs inclines up to 8° but cleans on slopes of up to 3°, and fits through openings 75 cm wide and at least 52 cm high.

In full coverage the MT1 cleans up to 1,800 m²/h, the MT1 Vac up to 1,400 m²/h and the MT1 Max up to 2,200 m²/h. In spot cleaning, when the AI sends the robot only where there is dirt, MT1 Vac, MT1 and MT1 Max reach 1,800, 6,000 and 7,000 m²/h. MT1 and MT1 Max serve areas in the order of 100,000 m². The number of robots depends on area, type of dirt, obstacles and time windows: we calculate it with you during the analysis phase.

It has two fans with two independent air ducts and a 55 cm wide suction nozzle. Suction efficiency rises by up to 200% and it even picks up 3 mm steel balls. The standard HEPA H11 filter retains over 98% of 0.3 µm particles; an H13 filter (99.97%) is available on request.

It uses LiDAR SLAM + VSLAM positioning, with markers as support, and fusion of several sensors to recognise fixed and moving obstacles. It cleans along walls and pillars and, at 49 cm high, passes under furniture and shelving with at least 52 cm of clearance. The 3D LiDAR, for high ceilings and low light, is fitted only on the MT1 Max.

The 60 Ah battery gives 3 to 6.5 hours of work depending on the mode: about 4 hours in sweeping + vacuuming on hard floors. Charging takes less than 3.5 hours, with the cable or automatically on the charging station, sold separately.

Yes, with the charging station, sold separately: when the battery is low the robot returns to base, charges and resumes work. Without the station it is charged with the cable. Charging takes about 3 hours for the MT1 and less than 3.5 hours for MT1 Vac and MT1 Max. The MT1 station requires a flat wall, 2 m clear in front and 1.5 m on each side.

Yes: the automatic emptying station is the new PUDU accessory for the MT1 series. The robot empties its bin into the station and goes back to work without staff having to intervene. In the quote we confirm compatibility with your model and the best position along the routes.

Yes, with the optional lift control and E-gate (automatic doors and gates) modules available for MT1, MT1 Vac and MT1 Max. This way the robot cleans several floors without anyone accompanying it. We check compatibility with your lift and doors during the site survey.

The air filter and the two 7-litre dust bags are changed every week. Side brushes and roller brush are cleaned every day and replaced every 6–12 months, like the rubber blades. The HEPA filter is not washable: it is cleaned every two days and replaced regularly. You will find the original H11 filter, dust cloths and seals among the accessories on this page.

Yes. With the PUDU Link app you see the status of all your PUDU robots on a single screen (online or offline, working, battery) and change tasks and schedules, even remotely. Each robot works in the areas and at the times you assign to it. Robot-to-robot calling is also available for collaborative cleaning between the MT1 and CC1 series: an MT1 robot can call a CC1 or a CC1 Pro. If you are interested, we check models and software versions with you.

Yes, through the PUDU Open Platform. The Cloud APIs allow an external system (ERP, WMS, facility management software) to read the status, activities and data of the cleaning robots, receive alerts via callbacks and, where available, send commands. With PUDU Skill, PUDU’s package for AI programming tools, developers write the integration faster. API access goes through the distributor: we activate it and check with PUDU which functions are available for your model.

We start by analysing areas, floors, dirt and schedules; on request we hold a demo at your premises. At installation we create the map, set up areas, routes and cleaning programmes and, if needed, connect lifts and doors. Then we train your staff: start-up, emptying, daily maintenance and use of the app. For support and spare parts you stay in direct contact with our technicians.

LeanProducts provides direct support throughout Italy through its own technicians. Types of support offered:

• phone support and remote access for questions or analysis;
• on-site repair or, preferably, shipment to our premises;
• specific training so you can work independently.

Yes, the manufacturer has signed a GDPR compliance declaration for CC1, CC1 Pro and the MT1 series. The robot does not record images of the surroundings and does not recognise faces. Where there is AI recognition of dirt and obstacles, each image stays in working memory, is analysed and deleted immediately, without being saved; recognition also works without internet. If needed, the RGB camera can be disabled and there is a blackout sticker: in that case the robot still cleans, but without recognising the type of dirt. Only operating data such as areas cleaned, tasks, status and faults goes to the PUDU cloud. We provide the declaration with the quote.

Yes. With PUDU Cloud Veil the data runs locally or on your private cloud and does not pass through PUDU servers: no data leakage at source and full control over the information, as required in environments with high confidentiality requirements. To connect the robot to your systems there is the PUDU Cloud Open API. We define the configuration and functions available for your model in the quote.

PUDU is certified ISO/IEC 27001:2022 for information security and ISO/IEC 27701:2019 for privacy, verified by the certification body DNV. Data is encrypted and stored encrypted, access is limited to authorised personnel and a dedicated department oversees information security. Vulnerabilities are reported through an official channel. On the robot, settings and working modes are password-protected and the software is updated remotely.

Yes, every robot comes with CE marking and an EU declaration of conformity. The CC1 Pro is certified to IEC 63327, the safety standard for automatic floor-cleaning machines for commercial use. For the other models we provide the declaration and the standards applied with the quote.