CC1 Pro multifunction cleaning robot with AI

They combine sweeping, scrubbing, vacuuming and dust mopping in a single robot, with four modes: sweeping and vacuuming of hard floors; scrubbing with dirty-water recovery; vacuuming of short-pile carpet; silent dust mopping. You choose the mode for each area. The CC1 Pro adds AI spot cleaning: it recognises stains and cleans them straight away.

During its round, the CC1 Pro uses cameras and artificial intelligence to recognise the most common wet stains, such as coffee, sauces and puddles, and immediately creates the route to clean them. In this mode it works only where needed and reaches 1500–3000 m²/h. On stubborn stains it increases cleaning power on its own. If a floor pattern is mistaken for a stain, you can exclude it from recognition.

On indoor floors of commercial, public and work buildings: supermarkets and shops, shopping centres, hotels, offices and residential buildings, schools, healthcare facilities, catering, stations and airports, factories and warehouses. They are not suitable for outdoors, stairs or heavy oil stains. Mirrors, glass and very dark surfaces between 14 and 22 cm above the floor can interfere with the LiDAR: we assess them during the site survey.

The rear AI camera looks at the floor after the pass: if it finds residual stains it goes over the area again and marks those that remain on the map. At the end of the job it generates the cleaning heat map; with Ultra Spot Clean you then quickly clean the areas where dirt appears most often. With guided cleaning the robot leads the operator to the stubborn stains.

They share the same base: 4-in-1 robot (sweeping, scrubbing, vacuuming, dust mopping), same dimensions and weight, 15 + 15 L tanks and 700–1,000 m²/h in full cleaning. The CC1 Pro adds artificial intelligence: spot cleaning of wet stains (coffee, sauces, puddles) at 1,500–3,000 m²/h; intensity adjusted automatically according to the dirt and floor type; rear AI camera that checks the result, re-cleans leftover stains and generates heat maps; self-diagnosis of brushes and squeegee; VSLAM+ navigation without ceiling markers; IEC 63327 certification. The CC1 carries out scheduled cleaning without visual analysis of the dirt.

In full-coverage cleaning the CC1 and CC1 Pro clean 700–1,000 m²/h, with a cleaning width of 500 mm (side brush included). The CC1 Pro reaches 1,500–3,000 m²/h in AI spot cleaning, when it only treats the detected stains, and covers 5,000–8,000 m² per cycle. Actual output depends on floor, soiling and routes: we estimate it with you during the analysis phase.

The battery is rated 50 Ah. Runtime by mode: scrubbing 5 hours; sweeping and vacuuming 5 hours; carpet vacuuming 4 hours; silent dust mopping 9 hours. Charging takes less than 3.5 hours; with the docking station the robot returns to recharge by itself.

Yes, with the (optional) docking station: when the battery is low the robot returns to the station by itself to recharge and, at the same station, refills clean water and drains waste water with no manual intervention. Without the station it is charged by cable.

No. The docking station connects to water, drain and power; where there is no water connection, it is combined with the mobile water station, with 30 L of clean water and 30 L of dirty water: no changes to the existing installation.

Yes, low-pile carpets and rugs, in vacuuming mode: the CC1 carpet vacuuming accessory is required. On carpet the robot vacuums and does not scrub. The CC1 Pro detects the change from hard floor to carpet by itself and switches mode.

No. The CC1 Pro uses PUDU VSLAM+ navigation, which combines vision and LiDAR and does not require QR codes or ceiling markers. It detects stationary and moving obstacles and recalculates the route when the space changes. During installation we map the premises and set up areas and routes.

Yes. The CC1 and CC1 Pro stay below 70 dB while cleaning. There is also a silent mode for dust mopping. The sensors (LiDAR, cameras, ultrasonic sensors, bumper) detect people and obstacles, whether stationary or moving: the robot stops or goes around them, and has an emergency stop button.

For each cleaning session you get the report, the map of the spots where waste accumulates and the performance heat map. The dashboard shows task completion, maintenance frequency and real-time alerts. The report history stays on the robot and in the cloud, and can be viewed with the PUDU Link app.

Yes. Several robots are managed from the same PUDU Link app, each with its own zones and schedules. Between the CC1 and MT1 series there is also collaborative cleaning: the CC1 Pro can call another robot to complete a zone or be called, for example by an MT1 that dry-sweeps.

Yes: with the optional lift kit the robot uses the lift and changes floor by itself, so it cleans the whole building. On the CC1 Pro, electronic gate control is also available as an option. During the site survey we check the lifts and the connections required.

Wi‑Fi is not essential: the robot also communicates via 4G and Bluetooth. The connection is used to manage it remotely with the PUDU Link app and to receive notifications and reports; during the site survey we check coverage along the routes with you.

Yes, through the PUDU Open Platform (Cloud API): your system starts, pauses or cancels cleaning runs, sends the robot to the station and receives status, errors, reports and statistics. For those developing the integration there is the PUDU Skill, a package for AI programming tools that knows the up-to-date PUDU APIs and speeds up the work. API access goes through the distributor: we activate it and support your IT team or integrator.

Routine maintenance is simple: empty the dirty-water tank every day or every other day, clean the dust bin and brushes every 2 days and the squeegee every 2–3 days, sensors and underside every 3–5 weeks. Squeegee blades and dust-cloth blades are changed every 1–3 months depending on use; roller brushes when the bristles reach the wear indicator. You can get original spare parts and consumables from us.

LeanProducts, official PUDU distributor in Italy, handles surface analysis, installation, mapping and staff training, with direct support throughout Italy. On request we organise a demo at your premises.

LeanProducts provides direct support throughout Italy through its own technicians. Types of support offered:

• phone support and remote access for questions or analysis;
• on-site repair or, preferably, shipment to our premises;
• specific training so you can work independently.

Yes, the manufacturer has signed a GDPR compliance declaration for CC1, CC1 Pro and the MT1 series. The robot does not record images of the surroundings and does not recognise faces. Where there is AI recognition of dirt and obstacles, each image stays in working memory, is analysed and deleted immediately, without being saved; recognition also works without internet. If needed, the RGB camera can be disabled and there is a blackout sticker: in that case the robot still cleans, but without recognising the type of dirt. Only operating data such as areas cleaned, tasks, status and faults goes to the PUDU cloud. We provide the declaration with the quote.

Yes. With PUDU Cloud Veil the data runs locally or on your private cloud and does not pass through PUDU servers: no data leakage at source and full control over the information, as required in environments with high confidentiality requirements. To connect the robot to your systems there is the PUDU Cloud Open API. We define the configuration and functions available for your model in the quote.

PUDU is certified ISO/IEC 27001:2022 for information security and ISO/IEC 27701:2019 for privacy, verified by the certification body DNV. Data is encrypted and stored encrypted, access is limited to authorised personnel and a dedicated department oversees information security. Vulnerabilities are reported through an official channel. On the robot, settings and working modes are password-protected and the software is updated remotely.

Yes, every robot comes with CE marking and an EU declaration of conformity. The CC1 Pro is certified to IEC 63327, the safety standard for automatic floor-cleaning machines for commercial use. For the other models we provide the declaration and the standards applied with the quote.