Skip to Content
  1. All Products
  2. AL Modular System
  3. Connection elements
  4. Connectors and fittings
  5. Quick connector 0°

Quick connector 0°

https://leanproducts.eu/web/image/product.template/3571/image_1920?unique=1d9bc53

Quick connector for joining two aluminium profiles with slot C8 or C10 at right angles: the head enters the slot, the bush goes into a hole near the end of the other profile. Up to 4000 N in slot C10, zinc-plated or stainless steel.

Read more ↓
Code: 3842535458
from
not with
options
Prices per piece + VAT
Prices per pack of %s + VAT
Prices per pack of %s pcs + VAT
colors
only
of
available
  • ESD
  • Slot
  • Surface treatment
  • Load capacity Fmax N
  • Tightening torque Nm
  • Production method
  • Technical notes
  • Moment Mmax Nm
  • Diameter mm
  • Bush
  • Brand
  • Material

This combination does not exist.

Log in to see prices and buy
You have already submitted a query for this product today.
Bosch 5SP
Contact Us
Request a quote
We reply within 1 working day
Download PDF data sheet

Specifications

Slot C10
ESD yes
Surface treatment Zinc plating
Load capacity Fmax N 4000
Moment Mmax Nm 140
Tightening torque Nm 25
Production method Moulding
Technical notes Small bush D9.8: hole does not touch the slot flanks; dist. 22.5 mm
Diameter mm 17
Bush D17
Brand Bosch Rexroth
Material zinc-plated steel
Tags
Tags
Bosch 5SP

Look at the slots of the two profiles: 8/8 if both have slot C8, 10/10 if both have slot C10, 8/10 if you join a C8 profile to a C10 one. In 10/10 the D17 bush carries more (4000 N), the D9.8 gives a cleaner joint. Then choose zinc-plated or stainless steel.

In the 90° the tie rod head is rotated 90° relative to the bush: choose according to how the bush hole is oriented relative to the slot of the cross profile. Load capacities and torques are the same; the 0° also has the mixed 8/10 version.

Choose the round head if the connected profile needs to rotate. If load capacity matters, use the standard connector: in 10/10 it holds 4000 N versus 2500 N, in 8/10 2000 N versus 500 N, in slot C6 450 N versus 250 N.

A blind or through hole for the bush, near the end of the profile: D11 in the 8/8 and 8/10 versions, D17 or D9.8 in the 10/10. The hole axis is 18 mm from the end on profiles with slot C8 and 22.5 mm on those with slot C10. With the drilling jig you can make it in the right position, even in the workshop.

It is a small bush: its hole does not touch the slot flanks, so the joint is cleaner and the slot can be closed completely with a cover profile. It holds less than the D17 (800 N versus 4000 N), has no standard drilling in the modulus 40, 50 and 60 profiles and is only available in zinc-plated steel.

When in slot C10 you need more load capacity (4000 N with bush D17) or a joint with no visible parts. However, the quick connector requires a hole in the profile for the bush; the tensioning connector does not.

Yes: the O-ring holds the connector in position while you tighten it. The connector can also be turned into the slot of the cross profile at the fixing point, so you don't have to slide it in from the end.

In the 90° connector the head of the tie rod is rotated 90° relative to the clamping bush. Choose one or the other according to how the bush hole is oriented relative to the slot of the cross profile. Load capacities and torques are the same; only the 0° has the mixed 8/10 version.

When the joint must withstand torsion: the device increases the torsional resistance of the profiles joined with the quick connector and can also be added later, once the connection is assembled. Available for slot C8 and C10.

Yes, but the hole position and load capacities change: with the radial compensation the bush axis goes 15 mm from the end in slot C8 and 19.5 mm in slot C10. Send us the joint and we'll confirm the values.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.

Accessory Products