Skip to Content
  1. All Products
  2. AL Modular System
  3. Feet and wheels
  4. Accessories for feet
  5. Spindle for levelling foot

Spindle for levelling foot

https://leanproducts.eu/web/image/product.template/3584/image_1920?unique=1d9bc53

Threaded spindle for modular levelling feet: M8, M12 or M16, lengths from 75 to 200 mm, in zinc-plated or stainless steel. Combine it with the base plate you need and compensate for uneven floors up to 10°. Up to 30000 N.

Read more ↓
Code: 3842537222
from
not with
options
Prices per piece + VAT
Prices per pack of %s + VAT
Prices per pack of %s pcs + VAT
colors
only
of
available
  • Brand
  • ESD
  • Load capacity Fmax N
  • Technical notes
  • Slot mm
  • Material
  • Thread
  • Length mm

This combination does not exist.

Log in to see prices and buy
You have already submitted a query for this product today.
Bosch 5S1
Contact Us
Request a quote
We reply within 1 working day
Download PDF data sheet

Specifications

Brand Bosch Rexroth
ESD yes
Load capacity Fmax N 10000
Technical notes Mandrino per piedi regolabili modulari; V 20 mm; compensa fino a 10°
Slot mm 8/10
Material stainless steel (ESD)
Thread M8
Length mm 75
Tags
Tags
Bosch 5S1

No, it is a fixed support. If the floor is not level use the levelling foot D30 or a modular foot with spindle and base plate.

The thread must match the threaded central hole of the profile and the load: M8 holds 10000 N, M12 20000 N, M16 30000 N. If the central hole of the profile is not suitable, use the plate for levelling foot, which carries the M12 or M16 thread.

Choose the length according to how much you need to adjust: with 75 or 85 mm you get 20–30 mm of adjustment, with 145 mm 80 mm, with 200 mm 135 mm. Long spindles are for very uneven floors or when you want to adjust the working height.

The load capacities are the same. Stainless steel performs better in damp environments or with frequent washing and is the version for ESD areas; zinc-plated is fine in dry environments.

Spindles and plates can be freely combined. Choose the plate according to the load and the floor: in PA up to 9000 N, in die-cast zinc or stainless steel up to 30000 N, with diameters from 29 to 79 mm. The load of the foot is the lower value of spindle and plate.

Add the PUR damping plate of the same diameter as the base plate: it damps vibrations and electrically insulates the foot. In an ESD area, connect the structure with the grounding set to discharge charges in a controlled way.

Yes, the spindle screws into an M8, M12 or M16 thread in the central hole of the profile. With the plate for levelling foot, the thread for the spindle is in the plate, which is fixed with screws in the holes of the profile.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.