Grooved plate 30x100 L/R

The grooved plate 30x100 L/R is the edge module of slotted tables: it has the same 25 mm pitch slots as the M plate plus a side 8 mm slot, which closes the table outwards and gives you a fixing point on the side. It joins the M plates with plastic sliding blocks, three per metre. Order it as a 5600 mm bar or cut to length from 100 mm.

Edge module 30x100 mmSide 8 mm slotSlot pitch 25 mm2.6 kg/m5600 mm bar

Why choose it

Closes the table

Fits on both edges of the slotted table, with the side slot facing outwards.

Slot on the side too

The side 8 mm slot gives you an extra fixing point on the edge.

Same pitch as the M

Slots at 25 mm pitch, like those of the centre plates.

Technical data

Property	Value
Code	3842993337 full bar · 3842993337L cut to length
Section	30x100 mm (edge module L/R)
Slot	Slots at 25 mm pitch with slot C8 connection technology, plus a side 8 mm slot
Cross-sectional area	A = 9.7 cm²
Weight	2.6 kg/m
Moment of inertia	Ix 88.8 cm⁴ · Iy 9.2 cm⁴
Section modulus	Wx 17.8 cm³ · Wy 6.0 cm³
Length	5600 mm (full bar) or cut to length
Minimum cut length	100 mm
Material	Anodised aluminium
Joining plates	Polyamide sliding block, 3 per metre of length

Full bar with the base code, piece cut to length with the same code followed by “L”.

Downloads

MGE catalogue pages 15 Download PDF

Related products

Grooved plate 30x100 MCentre plate 30x100 M

Plastic sliding block for grooved plate 30x100Plastic sliding block, 3 per metre

Aluminium strut profile 30x30Profile 30x30 for the frame

T-nutT-nut C8

Any other questions?Read the 11 FAQs →

Need help with your profile parts list?

Send us a sketch or the parts list: we will give you codes, accessories and cut lengths.

Request a quote Call +39 0434 572757

Specifications

Brand	Bosch Rexroth
Section mm	30x100
Slot mm	8
Cross-section area cm²	9.7
Moment of inertia Ix / Iy cm⁴	88.8 / 9.2
Section modulus Wx / Wy cm³	17.8 / 6.0
Max length mm	5600
Length	5600
Weight	2.6 kg/m
Material	Anodized aluminium

Usually both. The M is the centre module and sits next to other M plates; the L/R also has a side 8 mm slot and closes the table on both edges. For a 400 mm wide table, for example, use two M in the centre and two L/R at the sides.

It closes the table outwards and gives you an 8 mm slot on the side, where you can fix edge accessories using slot C8 technology.

Two per table, one per edge. Between them put as many M plates as you need to reach the width, in 100 mm steps.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.