Aluminium strut profile 80x80L slot 10

AL Modular System · C10 profiles

Aluminium strut profile 80x80L

The 80x80L is the large square profile of the 40 series: four 40 mm modules, two 10 mm slots per side and central bores that can be threaded M12. With Ix = Iy = 132.1 cm⁴ it is equally stiff in both directions: it is the post for support frames, gantries and columns receiving loads from several sides.

Section 80 × 80 mm8 slots of 10 mm4.9 kg/mIx = Iy 132.1 cm⁴40 series

Why choose it

Stiff in every direction

Ix = Iy 132.1 cm⁴: a post with no weak direction.

Two slots per side

Fix 40x40L or 40x80L crossbars with the slots aligned.

M12 central bores

Can be threaded M12 at the end for feet and connections; D17 for connectors.

Technical data

Property	Value
Code	3842993133
Section	80 × 80 mm
Slot	10 mm (C10)
Cross-sectional area	A = 18.2 cm²
Weight	4.9 kg/m
Moment of inertia	Ix 132.1 cm⁴ · Iy 132.1 cm⁴
Section modulus	Wx 33.0 cm³ · Wy 33.0 cm³
Torsion	It 59.80 cm⁴ · Wt 17.20 cm³
Bar length	6070 mm (usable length) or cut to length
Minimum cut length	50 mm
Alloy and finish	EN AW-6063 (AlMgSi), extruded, anodised E6/EV1 12 µm (300 HV)
Mechanical properties	Rm 245 N/mm² · Rp0.2 195 N/mm² · E 70 000 N/mm² · 75 HB
Tolerances	Straightness max 0.75 mm/m · torsion max 0.70 mm/m
Cover cap	Cover cap for profile 80x80 in PP, grey or black ESD
Series	40 series (40 mm modular dimension)
Standard machining	M12 thread in the central bores, D9.8 and D17 holes for connectors; profile machined up to 6000 mm
Packaging	Single bar or pack of 6 bars

The bar has the stated usable length: the physical piece is about 100 mm longer, because the anodising contact points remain at the ends.

Downloads

MGE catalogue pages 15 Download PDF

Related products

Aluminium strut profile 80x160LProfile 80x160L from the same series

Any other questions?Read the 10 FAQs →

Need help with your profile parts list?

Send us a sketch or the parts list: we will give you codes, accessories and cut lengths.

Request a quote Call +39 0434 572757

Specifications

Brand	Bosch Rexroth
Section mm	80x80
Slot mm	10
Max length mm	6070
Alloy	EN AW-6063 (Al MgSi)
Production method	Extrusion
Surface treatment	Anodising E6/EV1, 12 µm, 300 HV
Coefficient of thermal expansion	23.4 × 10⁻⁶ 1/K (+20…100 °C)
Tensile strength	245 N/mm²
Yield strength	195 N/mm²
Elongation at break	10%
Modulus of elasticity E	70000 N/mm²
Brinell hardness	75 HB
Straightness tolerance	max 0.75 mm/m
Torsion tolerance	max 0.70 mm/m
Min length mm	50
Cross-section area cm²	18.2
Torsion factor It cm⁴	59.80
Torsion factor Wt cm³	17.20
Section modulus Wx / Wy cm³	33.0 / 33.0
Moment of inertia Ix / Iy cm⁴	132.1 / 132.1
Weight	4.9 kg/m
Open slots	all slots open
Length	6070
Material	Anodized aluminium

When the post takes loads from several directions: the 80x80L has 132.1 cm⁴ on both axes, the 40x80L 63.4 in one direction and 17.3 in the other.

The cover cap for profile 80x80, grey or black ESD. For the 80x160L you need two side by side.

It is the width of the profile slot and determines which accessories you use. Slot C6 (6 mm) is for 20 series profiles, C8 (8 mm) for the 30 series, C10 (10 mm) for profiles from the 40 series upwards. Nuts, screws, brackets and cover caps are chosen by slot: each accessory's product page shows the right one.

Yes. You can order the full bar or the piece cut to the length you need: we do the cutting ourselves, in our workshop. Each profile's product page shows the maximum bar length and the minimum cut length.

Look at the moments of inertia Ix and Iy: the higher they are, the less the profile deflects under load. For the same section, “L” profiles are lightened and deflect a little more. For long spans or high loads move to a larger section or a tall profile (e.g. 45x90 instead of 45x45). If you send us drawing and loads, we will check the choice.

The T-nut is inserted from the front into the slot, even in an assembled structure, and positions itself when you tighten the screw: it is the standard choice for fixing accessories. The sliding block withstands higher forces, but normally has to be inserted from the profile end before closing the frame; spring versions stay where you put them.

The simplest way is the bracket, which joins two profiles at 90° with screws and nuts in the slot, without machining. For end, T, 45° or three-way connections there are dedicated connectors, some of which require profile machining as stated on their product page.

Yes, for several accessories (for example cover caps, hinges and nuts) there are conductive ESD versions, indicated in the name or variant. Tell us which EPA area you work in and we will confirm the components to use.

On each product page you will find the MGE catalogue pages to download as PDF, with dimensioned drawings and technical data; the Specifications tab shows the data for the variant you have chosen.

Yes. Send us the parts list or a sketch with dimensions: we give you codes, quantities and cut lengths and prepare the kit with profiles already cut and the accessories.